Used for testing standard bales. Attaches directly to the connector on top of the meter. For Delmhorst F6, F2000, FX2000 hay moisture meters and P2000 paper moisture meters.Not recommended for P2000 or RDM3-P as the density of paper bales causes undo...
Used for testing standard bales. Attaches directly to the meter. (18 inch version) For Delmhorst F6, F2000, FX2000 hay moisture meters and P2000 paper moisture meters.Not recommended for P2000 or RDM3-P as the density of
paper bales causes undo stress...
Use on roofs, insulation, or any tests deep below the surface. Pins are insulated, except at the tips. Maximum penetration of #608 pins is 3-1/4".
Two pins (insulated)
3 1/4" penetration
Use on EIFS, insulation and roofs
User replaceable contact pins for the BD10, BD2100 and JLite moisture meters by Delmhorst. Contact pin and retainer with overall penetration of 5/16". Standard on all J- and BD-series meters and the #2-E electrode. Used on wood up to 6/4, concrete and...
Pack of 24 contact pins used on the 26-ES hammer with 1/2" penetration.
4" pins (pack of 4) for the 21E probe by Delmhorst. Used on insulation.Standard on the #21-E, the #608 contact pins are insulated except at the tips. 4" overall length, 3 1/4" penetration.Also available as #608/001. 7" overall length, penetration of 6"...
Delmhorst MCS-1 Calibration standard (12% & 22%) Douglas Fir
The industry standard for lumber and woodworking, this electrode allows you to determine moisture gradients. The contact pins that come with the 26-ES have insulated shanks so that only the tips are exposed. The pins make contact with the wood fiber only...
Delmhorst H-4 Handle for use with P2000 Paper Moisture Meter and all Delmhorst Hay Type Moisture meters.
6" pins (pack of 4) for the 21E probe by Delmhorst. Used for testing EIFS.The #608/0014 contact pins are insulated except at the tips. 7" overall length, 6" penetration. Used for testing EIFS.Also available as #608/4. 4" overall length, 3 1/4"...
830-2: 10" Prod - for testing standard and high density bales. Use with H-4 Handle.
830-3: 18" Prod - for testing standard and high density bales. Use with H-4 Handle.
Pack of 20 - 3" concrete sleeves used with TotalCheck.
Retainer used to hold contact pins in place. Used with #496, #1849, and #A-111 pins. Available in packs of 4 as 632/4.
*We match all prices PLUS an extra 10% of the difference - just call!Advertised price must be lower than our total price when added to your cart*Delmhorst RH/Temp Sensor for TotalCheck, Navigator Pro & HT4000 For Concrete & Floor Testing. (Pack of 5)
Used for bales, 9 1/2" insulated pins, with 8 1/4" penetration, eliminate the effect of surface moisture
Now comes with a tapped handle 6' Extension cord for hard to reach places Two 5'' long blades, bent to a 35° angle Teflon coated w/ exposed tips Use to check behind trim and baseboard molding
Delmhorst Double roller type for measuring moisture content on a moving web.
Delmhorst 55-E Paper Electrode for use with the P2000 and RDM3P moisture meters.Leaf type for measuring moisture content on a moving web or roll. Can be used with a portable unit or for stationary installation.
Delmhorst 43-E Clamp Type moisture electrode. Clamp type for testing thin sheet stock. The sample tested is compressed between two smooth discs.